Painting for the City of Lincoln
TMI Coatings, Inc. (TMI), a QP 1 and QP 2 Certified Contractor, worked with the City of Lincoln in the winter of 2024/2025 on the removal and replacement of existing coatings on interior steel and concrete surfaces, asbestos abatement, lead abatement, and window replacement.
Project Overview:
- The project began with TMI setting up physical separation barriers across various critical areas to ensure safety and cleanliness. These barriers were placed over the filter beds, HVAC airways, stairwells, and doorways, isolating work zones from non-work areas. Additionally, TMI implemented containment strategies to protect the flooring, adjacent areas, and any items that were to remain in place throughout the project.
- Next, TMI proceeded with the removal and disposal of the existing metal duct enclosures and their supporting angles. The team carefully unscrewed the support angles from the ductwork, ensuring the structure was not compromised. After removing the support angles, TMI reinstalled new screws to maintain the integrity of the ductwork and the overall system.
- TMI used abrasive blasting techniques to clean and prepare various steel structures for recoating. This included steel beams, metal ducts, concrete beams, floor and roof decks, and walkways. Over 40 tons of abrasive was used and our sand vacuum followed along daily to collect and dispose of the spent sand. The blasting was followed by immediate priming and coating, using the same-day application of primer to ensure no rust or contamination occurred between stages. This step ensured that the steel was adequately protected against corrosion.
- TMI also cut out and replaced select steel angle frames along trenches and did mortar repair. After the repairs were made, the floor plates were abrasive blasted on all sides and recoated before being reinstalled.
- TMI removed rust and old paint from overhead steel members, reapplying a fresh coat of paint to restore their appearance.
- As part of the second phase of the project, TMI conducted lead abatement for the City of Lincoln. This involved a careful, regulated processes to safely remove lead-based paints ensuring a safe environment for workers.
- Before commencing abrasive blasting, TMI performed a chemical wash using Chlor-Rid to prepare the surfaces. The chemical wash helped remove contaminants and residues, ensuring that the surface was fully prepared for the blast and subsequent coating.
- TMI followed the SSPC SP6 Commercial blast clean standard, which included a three-step coating process:
- Stripe Coat: Applied SW Dura-Plate 235 with a dry film thickness (DFT) of 5-7 mils
- Prime Coat: Applied a second layer of SW Dura-Plate 235 with the same DFT.
- Finish Coat: SW Sher-Loxane 800 was applied as the final finish coat, providing a protective and aesthetically pleasing finish.
- The project also required cleaning and recoating of metal ducts. TMI applied the same cleaning and coating process, starting with a chemical wash (Chlor-Rid), followed by an abrasive blasting treatment (SSPC SP7 Brush-off blast clean). The coating process included the application of SW Macropoxy 5000 as the primer (1-2 mil DFT) and a finish coat of SW Acrolon 7300 in Cylinder Cream SW-4005 (2-8 mil DFT).
- Concrete beams, floor decks, and roof decks were also treated. TMI performed abrasive blasting to clean the concrete surfaces in compliance with SSPC standards. Following the blasting, a prime coat of SW Dura-Plate 235 was applied, followed by a finish coat of Sher-Loxane 800 in Cylinder Cream, ensuring long-lasting protection for the concrete surfaces.
- TMI worked on the concrete floor walking surfaces and patched the edges of floor access panels. These surfaces were also cleaned by SSPC SP6 Commercial blast cleaning, and then recoated with a prime coat of SW Dura-Plate 235 and a finish coat of SW Sher-Loxane 800.
Conclusion
Throughout this project for the City of Lincoln, TMI collected abrasive dust with a 35,000 CFM dust collection unit. Spent abrasive was tested for proper disposal in compliance with safety and environmental regulations. TMI Coatings. Safety. Quality. On time. In that order.
With over 35 years of experience, TMI Coatings will have your project completed on time and within budget. Contact us today at 651-452-6100 for your free, no-obligation quote.









